A vulnerability in the Switch Integrated Security Features of Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause an interface queue wedge. The vulnerability is due to incorrect handling of crafted IPv6 packets. An attacker could exploit this vulnerability by sending crafted IPv6 packets through the device. An exploit could allow the attacker to cause an interface queue wedge. There are no workarounds that address this vulnerability. This advisory is available at the following link: https://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20180328-sisf
This vulnerability affects the Cisco cBR-8 Converged Broadband Router, Cisco ASR 1000 Series Aggregation Services Routers, and Cisco Cloud Services Router 1000V Series when configured with IPv6.
In the field and internal testing, this vulnerability was only observed or reproduced on the Cisco cBR-8 Converged Broadband Router. The Cisco ASR 1000 Series Aggregation Services Routers and Cisco Cloud Services Router 1000V Series contain the same code logic, so affected trains have had the code fix applied; however, on these two products, the vulnerability has not been observed in the field or successfully reproduced internally.
For information about which Cisco IOS XE Software releases are vulnerable, consult the Cisco bug ID(s) at the top of this advisory.
Administrators can identify interfaces that have assigned IPv6 addresses by using the show ipv6 interface brief command in the CLI. The following example shows the output of the command on a device with IPv6 enabled:
router#show ipv6 interface brief . . . GigabitEthernet0/0/0 [Up/Up] fe80::212:daff:fe62:c150 2001:DB8::1
If IPv6 is not supported by the software release that is running on a device, using the show ipv6 interface brief command produces an error message. If IPv6 is not enabled on the device, using the show ipv6 interface brief command does not show any interfaces with IPv6 addresses. In either scenario, the device is not affected by this vulnerability.
To determine which Cisco IOS XE Software release is running on a device, administrators can log in to the device, use the show version command in the CLI, and then refer to the system banner that appears. If the device is running Cisco IOS XE Software, the system banner displays Cisco IOS Software, Cisco IOS XE Software, or similar text.
The following example shows the output of the command for a device that is running Cisco IOS XE Software Release 16.2.1 and has an installed image name of CAT3K_CAA-UNIVERSALK9-M:
Vulmon
ios-xe-device# show version
Cisco IOS Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version Denali 16.2.1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Sun 27-Mar-16 21:47 by mcpre
.
.
.
For information about the naming and numbering conventions for Cisco IOS XE Software releases, see the Cisco IOS and NX-OS Software Reference Guide.
Router#show interface | include Input queue
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
Input queue: 376/375/0/0 (size/max/drops/flushes); Total output drops: 0
Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0
Router#
Once the identified interface is known, capture the output of the show buffers input-interface [interface] packet and show buffers input-interface [interface] dump CLI commands and contact your local support organization.
For detailed information about fixed software releases, consult the Cisco bug ID(s) at the top of this advisory.
For a mapping of Cisco IOS XE Software releases to Cisco IOS Software releases, refer to the Cisco IOS XE 2 Release Notes, Cisco IOS XE 3S Release Notes, or Cisco IOS XE 3SG Release Notes, depending on the Cisco IOS XE Software release.
When considering software upgrades, customers are advised to regularly consult the advisories for Cisco products, which are available from the Cisco Security Advisories and Alerts page, to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to be upgraded contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
| Version | Description | Section | Status | Date |
|---|---|---|---|---|
| 1.0 | Initial public release. | - | Final | 2018-March-28 |
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.