Multiple Cisco products contain vulnerabilities in the processing of H.323 messages, which are typically used in Voice over Internet Protocol (VoIP) or multimedia applications. A test suite has been developed by the University of Oulu to target this protocol and identify vulnerabilities. Support for the H.323 protocol was introduced in Cisco IOS® Software Release 11.3T. Release 11.3T, and all later Cisco IOS releases may be affected if the software includes support for voice/multimedia applications. Vulnerable devices include those that contain software support for H.323 as network elements as well as those configured for IOS Network Address Translation (NAT) and those configured for IOS Firewall (also known as Context-Based Access Control [CBAC]). Other Cisco voice products that do not run Cisco IOS may also be affected. These vulnerabilities can be exploited repeatedly to produce a denial of service (DoS). This advisory is available at http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20040113-h323.
Multiple Cisco products contain vulnerabilities in the processing of H.323 messages, which are typically used in Voice over Internet Protocol (VoIP) or multimedia applications. A test suite has been developed by the University of Oulu to target this protocol and identify vulnerabilities.
Support for the H.323 protocol was introduced in Cisco IOS® Software Release 11.3T. Release 11.3T, and all later Cisco IOS releases may be affected if the software includes support for voice/multimedia applications. Vulnerable devices include those that contain software support for H.323 as network elements as well as those configured for IOS Network Address Translation (NAT) and those configured for IOS Firewall (also known as Context-Based Access Control [CBAC]).
Other Cisco voice products that do not run Cisco IOS may also be affected.
These vulnerabilities can be exploited repeatedly to produce a denial of service (DoS).
This advisory is available at http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20040113-h423.
This section provides details on affected products.
All Cisco products that run Cisco IOS software and support H.323 packet processing are affected. This may include devices configured for Session Initiation Protocol (SIP) or Media Gateway Control Protocol (MGCP), since support for these protocols can enable support for H.323. Cisco IOS images with the "PLUS" feature set may be vulnerable regardless of their configuration because of a bug that enables H.323 by default and does not allow the protocol to be turned off.
Other affected products that do not run Cisco IOS software include:
Note: Cisco ATA 18x series products are only vulnerable when configured for H.323. They are not vulnerable when configured for SIP.
To determine the software running on a Cisco product, log in to the device and issue the show version command to display the system banner. Cisco IOS Software will identify itself as "Internetwork Operating System Software" or simply "IOS." On the next line of output, the image name will be displayed between parentheses, followed by "Version" and the IOS release name. Other Cisco devices will not have the show version command or will give different output.
The following example identifies a Cisco product running Cisco IOS Software Release 12.0(3) with an installed image name of C2500-IS-L. The release train label is 12.0.
Cisco Internetwork Operating System Software IOS (TM) 2500 Software (C2500-IS-L), Version 12.0(3), RELEASE SOFTWARE
The following example shows a product running Cisco IOS Software Release 12.0(2a)T1 with an image name of C2600-JS-MZ.
Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-MZ), Version 12.0(2a)T1, RELEASE SOFTWARE (fc1)
Additional information about Cisco IOS version naming is available at http://www.cisco.com/warp/public/620/1.html.
If you are running Cisco IOS versions 10.x, 11.1, 11.2 or earlier, you are not affected.
Cisco IOS Processing of H.323 Traffic
There are three areas where IOS can be vulnerable to malformed H.323 packets. Please read the following sections to determine if your router is affected. If you need to open a TAC case, please capture the output of the suggested identification steps to speed your case resolution.
Note: If you choose to block H.323 traffic using an access list to prevent H.323 traffic from entering the router, you will have protected your device from the vulnerability described in this Advisory and the details listed below will not apply to you. Please see the Workarounds section for more details on how to do this. Cisco recommends that customers upgrade to an appropriate IOS image at their earliest convenience.
To determine if your Cisco IOS device is processing H.323 traffic and is possibly vulnerable, it is necessary to understand the three different ways that Cisco IOS software processes H.323 traffic.
1. H.323 Endpoints
This includes H.323 Gateway, H.323 Gatekeeper, and H.323 Gatekeeper with Proxy, as well as releases that may run the H.323 process by default without being configured. Please continue with the following steps to determine if your device is affected.
From the enable prompt, run the show process cpu command and look for a process called CCH323_CT. In later versions of Cisco IOS software, you can execute the show process cpu | include CCH323.
Router# show process cpu | include CCH323 112 Mwe 60F3E5E0 295112 239401 123220072/24000 0 CCH323_CT
Note: Only images with a "PLUS" feature set (such as IP PLUS, ENTERPRISE PLUS) support voice and will have the CCH323_CT process running. In 12.0, the "PLUS" feature set has the CCH323_CT process running by default on the 2600 and 3600 platforms. Starting in 12.1, the process will run by default if you have a voice card or dsp card inserted.
Note: This will drop all calls being managed by the gatekeeper. Perform this only when you can safely stop gatekeeper functionality.
- If you are using H.323 proxy, your options are to either configure an access list to restrict TCP port 1720 traffic to known, trusted IP addresses, or to upgrade your IOS version.Router(config)#no proxy h423 Router(config)#gatekeeper Router(config-gk)#shutdown Router(config-gk)#no shutdown
2. IOS Firewall (Context-Based Access Control)
If your IOS device is configured to use IOS Firewall (IOS FW, or
Context-Based Access Control [CBAC]), check to see if IOS FW is running on the
device by issuing the show ip inspect all command.
Look for the following lines indicating that IOS FW is applied to an interface.
In this case, inspection rule "
Interface Configuration Interface FastEthernet0/0 Inbound inspection rule istcp alert is on audit-trail is off timeout 3600 h423 alert is on audit-trail is off timeout 3600 Outgoing inspection rule is not set
Router#config t Router(config)#Interface FastEthernet 0/0 Router(config-if)#no ip inspectin
Router#config t Router(config)#Interface FastEthernet 0/0 Router(config-if)#no ip inspectout
Router(config)#no ip inspect nameh423
Cisco recommends that you upgrade your IOS as soon as possible.
3. IOS Network Address Translation (NAT)
If you have configured NAT rules and have NAT activated on any interface, check to see if NAT is configured and activated on the device by issuing the show ip nat statistics command.
Router#show ip nat statistics Total active translations: 3 (3 static, 0 dynamic; 0 extended Outside interfaces Inside interfaces Hits: 0 Misses: 0 Expired translations: 0 Dynamic mappings:
Total active translations: 3 (3 static, 0 dynamic; 0 extended Outside interfaces: Serial3/0 Inside interfaces: Serial1/0 Hits: 0 Misses: 0 Expired translations: 0 Dynamic mappings:
If you see any of the above lines without the overload, route-map, or extendable keywords, then you are vulnerable.ip nat outside source ... ip nat inside destination ... ip nat inside source ...
The following examples would be vulnerable.ip nat (inside|outside) source static tcp ip-addr (port|1720) ip-addr (1720|port)
The following examples would not be vulnerable.ip nat inside source static tcp 10.1.0.1 1720 10.2.0.1 5834 ip nat outside source static tcp 10.15.12.1 6884 10.6.7.1 1720 ip nat inside source static tcp 10.1.0.17 1720 10.33.14.1 1720
If any of your configuration lines are vulnerable, please consult the Workarounds section.ip nat inside source static tcp 10.1.0.17 53 10.33.14.1 53 ip nat outside source static udp 10.1.14.75 1720 10.131.1.1 6888
To determine if a particular Cisco IOS release is vulnerable, consult the list below in the Software Versions and Fixes section to determine if the product is running an affected version of software.
The following list of Cisco products is provided specifically to list those products that customers may also be concerned about in regards to these vulnerabilities. The products below are not affected either because they are not vulnerable or because they do not support H.323 processing. Any other Cisco products that have not been identified as vulnerable or have been omitted from the list below should be considered as not vulnerable, as no other Cisco products are known to be affected by these vulnerabilities.
H.323 is the International Telecommunications Union (ITU) standard for real-time multimedia communications and conferencing over packet-based (IP) networks. A subset of the H.323 standard is H.225.0, a standard used for call signalling protocols and media stream packetization over IP networks.
The H.225.0 standard defines message formats for call setup, call control, and communications using Abstract Syntax Notation One (ASN.1). ITU Standard Q.931, which was developed for call signalling purposes in ISDN networks, is also used as the standard for the call setup messages within H.225.0.
The University of Oulu Secure Programming Group (OUSPG) has created a test suite for H.323, more specifically the H.225.0 and Q.931 messages, to help support proactive discovery and resolution of vulnerabilities in the processing of H.323 messages. The test suite is generally used to analyze a protocol and produce messages that probe various design limits within an implementation of a protocol. Test packets containing overly long or exceptional elements in various fields of the H.323 Protocol Data Units (PDUs) can be programmatically generated and then transmitted to a network device under test. The PROTOS test suite for H.323, as distributed, contains approximately 4500 individual test cases.
The vulnerabilities discovered in the affected products can be easily and repeatedly demonstrated with the use of the OUSPG PROTOS Test Suite for H.323. The largest group of vulnerabilities described in this advisory result from insufficient checking of H.225.0 messages as they are received and processed by an affected system. Malformed H.225.0 messages received by affected systems can cause various parsing and processing functions to fail, which may result in a system crash and reload (or reboot) in most circumstances.
Typically, H.323 network elements implement call signalling over both UDP and TCP transports on port 1720. The H.323 test suite from OUSPG only tests the TCP implementation on port 1720 by default.
Cisco IOS
Cisco IOS Software Release |
Description of Vulnerability |
---|---|
11.1, 11.2, 11.3, 12.3 |
Not vulnerable |
11.3T, 12.0, 12.0S,12.0T, 12.1, 12.1T, 12.1E, 12.2, 12.2S, 12.2T |
Vulnerabilities exist in the processing of H.323 Network Element traffic. This includes H.323 Gateway, H323 Gatekeeper, and H.323 Gatekeeper with Proxy. |
12.1, 12.1E, 12.2, 12.2T, 12.2S, 12.3T |
Vulnerabilities exist in the processing of H.323 IOS NAT traffic. |
12.0, 12.1, 12.1E, 12.2, 12..2T, 12.2S |
Vulnerabilities exist in the processing of H.323 IOS Firewall (CBAC) traffic. |
The vulnerabilities in Cisco IOS for devices acting as H.323 dial-peer endpoints are documented in the following Bug IDs: CSCdt09262 ( registered customers only) , CSCdt54401 ( registered customers only) , CSCdw14262 ( registered customers only) , CSCdx76632 ( registered customers only) , CSCdx77253 ( registered customers only) , CSCea19885 ( registered customers only) , CSCea32240 ( registered customers only) , CSCea36231 ( registered customers only) , CSCea33065 ( registered customers only) , CSCea42826 ( registered customers only) , CSCea42527 ( registered customers only) , CSCea44227 ( registered customers only) , CSCea44309 ( registered customers only) , CSCea46342 ( registered customers only) , and CSCec79541 ( registered customers only) .
For those Cisco IOS devices acting as a H.323 gatekeeper with proxy configured, the vulnerabilities are documented in the following Bug IDs: CSCea51076 ( registered customers only) , CSCea51030 ( registered customers only) , and CSCea54851 ( registered customers only) .
Cisco IOS devices performing NAT translations on H.323 v3/4 traffic may be vulnerable. Releases based off 12.2T must be running a version of IOS that is based off 12.2(11)T or later and must have the hidden command ip nat service h423all enabled. The default condition for this command is disabled. In releases based off 12.1 and 12.1E, the device is only vulnerable to packets sent from the outside interface to the inside interface. This means that networks are only vulnerable if they have static translations configured and accept connections to port 1720. A dynamic translation can occur on port 1720, but the attack traffic would then have to return from the destination address of the original flow and must traverse the router while the translation is still active. Methods to reduce exposure for dynamic translations are listed in the Workarounds section.
The vulnerabilities in Cisco IOS for devices doing NAT on H.323 packets starting in IOS 12.1 are documented in the following Bug IDs: CSCdr48143 ( registered customers only) , CSCdx40184 ( registered customers only) , CSCea27536 ( registered customers only) , CSCec76694 ( registered customers only) , and CSCed28873 ( registered customers only) .
The vulnerabilities in Cisco IOS for devices running IOS Firewall Feature Set doing deep packet inspection of H.323 packets in IOS starting in 12.1 are documented in the following Bug IDs: CSCec76776 ( registered customers only) and CSCec87533 ( registered customers only) .
Cisco CallManager
The vulnerabilities in Cisco CallManager are documented in Bug IDs CSCdx82831 ( registered customers only) , CSCea46545 ( registered customers only) , and CSCea55518 ( registered customers only) .
In order for a Cisco CallManager running 3.1 or 3.2 to be vulnerable, the IP address of the originating device must be configured as a H.323 gateway, H.323 client, or intercluster trunk on the CallManager, or "Allow Anonymous Calls" must be enabled in the gatekeeper section of the CallManager configuration. If a CallManager receives H.323 messages from a device that is not configured as an H.225.0 device, the TCP session will be closed before the H.225.0 message is processed. If "Allow Anonymous Calls" is enabled in the gatekeeper configuration, the CallManager server is vulnerable since it will try to parse the H.225.0 message from any originating source.
In CallManager 3.3, the server is vulnerable and will try to parse H.225.0 messages received from any originating source, but the CallManager may be listening on a port other than TCP 1720. Since the port number for anonymous calls is something other than TCP 1720, a potential attacker would need to determine which random port the CallManager H.323 gateway is listening on in order to carry out a successful attack.
Cisco Conference Connection
All versions of Cisco Conference Connection (CCC) are affected. There are currently no software fixes planned for Cisco Conference Connection (CCC). Customers running CCC should implement a workaround to limit H.323 traffic from trusted hosts only. A workaround for this may be found in the Workarounds section.
Cisco Internet Service Node
All versions of Internet Service Node (ISN) are affected. There are currently no software fixes planned for Cisco Internet Service Node (ISN). Customers running ISN should implement a workaround to limit H.323 traffic from trusted hosts only. A workaround for this may be found in the Workarounds section.
Cisco 7905 Series IP Phone
The vulnerabilities in the Cisco 7905 IP Phone are documented in Bug ID CSCec77152 ( registered customers only) .
Cisco ATA18x Series Analog Telephony Devices
The vulnerabilities in the Cisco ATA18x devices are documented in Bug IDs CSCea46231 ( registered customers only) , CSCea48726 ( registered customers only) and CSCef42352 ( registered customers only) .
Cisco BTS 10200 Softswitch
The vulnerabilities in the Cisco BTS 10200 Softswitch are documented in BugID CSCea48755 ( registered customers only) .
Workarounds for H.323 endpoint and proxy configurations
Affected devices that must run H.323 are vulnerable, and there are not any specific configurations that can be used to protect them. Applying access lists on interfaces that should not accept H.323 traffic and putting firewalls in strategic locations may greatly reduce exposure until an upgrade can be performed.
The Voice over IP SAFE paper talks about a variety of best practices that should keep your voice network isolated from the Internet. This reduces the risk of exposure, although attacks from within the local network should always be considered a potential risk.
Below is an example of an access list to block H.323 management traffic from anywhere but a permitted network. In this example, the permitted network is 172.16.0.0/16.
!--- Permit access from any IP address in the 172.16.0.0/16 !--- network to anywhere on port 1720. access-list 101 permit tcp 172.16.0.0 0.0.255.255 any eq 1720 !--- Permit access from anywhere to a host in the !--- 172.16.0.0/26 network on port 1720. access-list 101 permit tcp any 172.16.0.0 0.0.255.255 eq 1720 !--- Deny all traffic from port 1720. access-list 101 deny tcp any eq 1720 any !--- Deny all traffic to port 1720. access-list 101 deny tcp any any eq 1720 !--- Permit all other traffic. access-list 101 permit ip any any
Workarounds for IOS devices performing NAT on H.323 traffic
Cisco IOS devices that run an affected version of 12.1 or 12.1E code and are configured to do static NAT are vulnerable to attacks with corrupted packets being processed by NAT through the device. There are several methods of reducing or removing the risk in these circumstances.
interface serial 0/0 ip nat outside !--- This is used to indicate which interface !--- this configuration should be applied to. ip access-group 101 in ! access-list 101 deny tcp any eq 1720 any access-list 101 deny tcp any any eq 1720 access-list 101 permit ip any any
interface Null0 no ip unreachables ! interface Ethernet0/0 ip address 10.0.0.8 255.255.255.0 ip nat inside ! interface Ethernet0/1 ip address 11.0.0.8 255.255.255.0 ip nat outside ip policy route-map block-h423 ip nat inside source static 10.0.0.5 1.0.0.5 access-list 102 permit tcp any host 1.0.0.5 eq 1720 access-list 102 permit tcp any eq 1720 host 1.0.0.5 route-map block-h423 permit 10 match ip address 102 set interface Null0
Note: This will prevent users from using NAT for H.323-enabled applications from their PC desktops, such as NetMeeting. It is critical to understand your network and the applications in use on it when applying this type of workaround.
interface Ethernet0/0 ip address 10.0.0.8 255.255.255.0 ip nat inside ! interface Ethernet0/1 ip address 11.0.0.8 255.255.255.0 ip nat outside ip nat pool h423-test 1.0.0.5 1.0.0.15 prefix-length 24 ip nat inside source route-map h423-block pool h423-test access-list 101 deny tcp any any eq 1720 access-list 101 deny tcp any eq 1720 any access-list 101 permit ip host 10.0.0.0 0.0.0.255 route-map h423-block permit 10 match ip address 101
Defining a Windows-based access control list to limit H.323 traffic from only locally trusted hosts
There is an executable file available here named IPSec-H323.exe that contains scripts to aid in the configuration of access lists for Microsoft Windows 2000-based servers:
http://www.cisco.com/pcgi-bin/tablebuild.pl/cmva-3des?psrtdcat20e2
This workaround has been tested to work with both Cisco Conference Connection and Internet Service Node to block potentially harmful H.323 packets. Please consult the IPSec-H323-Readme.htm file that is also available at the above link for further details regarding the scripts.
Cisco IOS Software
Each row of the table describes a release train and the platforms or products for which it is intended. If a given release train is vulnerable, then the earliest possible releases that contain the fix and the anticipated date of availability for each are listed in the Rebuild, Interim, and Maintenance columns. In some cases, no rebuild of a particular release is planned; this is marked with the label "Not scheduled." A device running any release in the given train that is earlier than the release in a specific column (less than the earliest fixed release) is known to be vulnerable, and it should be upgraded at least to the indicated release or a later version (greater than the earliest fixed release label).
When selecting a release, keep in mind the following definitions.
In all cases, customers should exercise caution to be certain the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, contact the Cisco TAC for assistance, as shown in the section following this table.
Note: For the purposes of the table below, the identifier "Element" covers the fixes for IOS devices running as H.323 endpoints and as gatekeepers with proxy configured.
Train |
Vulnerable Configuration |
Availability of Fixed Releases |
||
---|---|---|---|---|
10.x-based Releases |
Not Vulnerable |
|||
11.x-based Releases |
Rebuild |
Interim |
Maintenance |
|
11.0 |
Not Vulnerable |
|||
11.1 |
Not Vulnerable |
|||
11.1AA |
Not Vulnerable |
|||
11.1CA |
Not Vulnerable |
|||
11.1CC |
Not Vulnerable |
|||
11.2 |
Not Vulnerable |
|||
11.2P |
Not Vulnerable |
|||
11.2SA |
Not Vulnerable |
|||
11.3 |
Not Vulnerable |
|||
11.3T |
Introduced H.323 feature in 11.3(3)T Vulnerable No Software Fixes Scheduled Migrate to 12.0 |
|||
12.0-based Releases |
Rebuild |
Interim |
Maintenance |
|
12.0 |
Element |
12.0(27) |
||
NAT |
Not Vulnerable |
|||
IPFW |
12.0(28) |
|||
12.0D |
Not Vulnerable |
|||
12.0DA |
Not Vulnerable |
|||
12.0DC |
Not Vulnerable |
|||
12.0S |
Element |
2600/3600 Platforms ONLY 12.0(25)S1, 12.0(24)S2, 12.0(23)S3 |
2600/3600 Platforms ONLY 12.0(26)S |
|
NAT |
Not Vulnerable |
|||
IPFW |
Not Vulnerable |
|||
12.0SC |
Not Vulnerable |
|||
12.0SL |
Not Vulnerable |
|||
12.0SP |
Not Vulnerable |
|||
12.0ST |
No fixes planned, only 2600/3600 platforms vulnerable |
|||
12.0SX |
Not Vulnerable |
|||
12.0SY |
Not Vulnerable |
|||
12.0SZ |
Not Vulnerable |
|||
12.0T |
Vulnerable. No fixes planned. |
|||
12.0W5 |
Not Vulnerable |
|||
12.0WC |
Not Vulnerable |
|||
12.0WT |
Not Vulnerable |
|||
12.0XC |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XD |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XG |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XH |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XI |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XJ |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XK |
Vulnerable. Migrate to 12.2(19)b |
|||
12.0XL |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XN |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XQ |
Vulnerable. Migrate to 12.1(22) |
|||
12.0XR |
Vulnerable. Migrate to 12.2(19)b |
|||
12.0XT |
Vulnerable. No migration path |
|||
12.1-based Releases |
Rebuild |
Interim |
Maintenance |
|
12.1 |
Element |
12.1(22) |
||
NAT |
12.1(22) |
|||
IPFW |
12.1(22) |
|||
12.1AA |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1AX |
Not Vulnerable |
|||
12.1AY |
Not Vulnerable |
|||
12.1DA |
Not Vulnerable |
|||
12.1DB |
Not Vulnerable |
|||
12.1DC |
Not Vulnerable |
|||
12.1E |
Element |
12.1(20)E2 |
||
NAT |
12.1(13)E13, 12.1(20)E2 12.1(8b)E18, 12.1(11b)E14, 12.1(14)E10, 12.1(19)E6 - available by 16-Jan-2004 |
|||
IPFW |
12.1(8b)E16, 12.1(11b)E14, 12.1(13)E12, 12.1(14)E9, 12.1(19)E6, 12.1(20)E2 |
|||
12.1EA |
Not Vulnerable |
|||
12.1EB |
Not Vulnerable |
|||
12.1EC |
Vulnerable No migration path No fixed release |
|||
12.1EV |
Not Vulnerable |
|||
12.1EW |
Not Vulnerable |
|||
12.1EX |
Not Vulnerable |
|||
12.1EY |
Not Vulnerable |
|||
12.1EZ |
Vulnerable Not yet migrated No rebuild planned |
|||
12.1T |
Element |
12.1(5)T17 |
Migrate to 12.2(19)b |
|
NAT |
12.1(5)T17 |
Migrate to 12.2(19)b |
||
IPFW |
12.1(5)T17 |
Migrate to 12.2(19)b |
||
12.1X(l) |
12.1X releases generally migrate to 12.1T, 12.2 or 12.2T as specified below. Please refer to specific train technical notes for documented migration path. |
|||
12.1XA |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1XB |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XC |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1XD |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1XF |
Not Vulnerable |
|||
12.1XG |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XH |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1XI |
Vulnerable. Migrate to 12.2(19)b |
|||
12.1XJ |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XL |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XM |
Vulnerable. Migrate to 12.2(2)XB15 |
|||
12.1XP |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XQ |
Vulnerable. Migrate to 12.2(2)XB15 |
|||
12.1XR |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XT |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1XU |
Vulnerable. Migrate to 12.2(4)T6 |
|||
12.1XV |
Vulnerable. Migrate to 12.2(2)XB15 |
|||
12.1XW |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YB |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YC |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YD |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YE |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YF |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YH |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YI |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.1YJ |
Not Vulnerable |
|||
12.2-based Releases |
Rebuild |
Interim |
Maintenance |
|
12.2 |
Element |
12.2(10g), 12.2(13c), 12.2(16a) |
12.2(17) |
|
NAT |
12.2(19b) 12.2(21a) 12.2(10g), 12.2(13e), 12.2(16f), 12.2(17d) - available by 16-Jan-2004 |
|||
IPFW |
Not Vulnerable |
|||
12.2B |
Migrate to 12.3(4)T |
|||
12.2BC |
Not Vulnerable |
|||
12.2BW |
Migrate to 12.2(15)T5 |
Migrate to 12.3(3e) |
||
12.2BX |
Vulnerable No migration path |
|||
12.2BZ |
Not Vulnerable |
|||
12.2CX |
Not Vulnerable |
|||
12.2CY |
Not Vulnerable |
|||
12.2DA |
Not Vulnerable |
|||
12.2DD |
Vulnerable. Migrate to 12.3(3e) |
|||
12.2DX |
Vulnerable. Migrate to 12.3(3e) |
|||
12.2JA |
Not Vulnerable |
|||
12.2MB |
Not Vulnerable |
|||
12.2MC |
Vulnerable No planned release |
|||
12.2MX |
Vulnerable. Migrate to 12.3(4)T1 |
|||
12.2S |
Element |
12.2(14)S3 |
12.2(18)S |
|
NAT |
12.2(14)S7 available Feb-23-2004 12.2(18)S3 available Jan-19-2004 |
|||
IPFW |
Not Vulnerable |
|||
12.2SX |
Element |
12.2(17a)SXA |
||
NAT |
12.2(17a)SXA |
|||
IPFW |
TBD |
|||
12.2SY |
12.2(14)SY3 |
|||
12.2SZ |
Not Vulnerable |
|||
12.2T |
Element |
12.2(4)T6, 12.2(8)T10, 12.2(11)T9, 12.2(13)T5, 12.2(15)T2 |
No more maintenance trains for 12.2T are planned. Please migrate to the latest 12.3 Mainline release. |
|
NAT |
12.2(4)T6, 12.2(8)T10, 12.2(11)T8, 12.2(13)T3, 12.2(15)T5 |
No more maintenance trains for 12.2T are planned. Please migrate to the latest 12.3 Mainline release. |
||
IPFW |
12.2(4)T8 |
No more maintenance trains for 12.2T are planned. Please migrate to the latest 12.3 Mainline release. |
||
12.2XA |
Vulnerable. Migrate to 12.2(11)T9 |
|||
12.2XB |
Element |
12.2(2)XB14 |
||
NAT |
12.2(2)XB14 |
|||
IPFW |
12.2(2)XB15 |
|||
12.2XC |
Vulnerable. Migrate to 12.3(3e) |
|||
12.2XD |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XE |
Not Vulnerable |
|||
12.2XF |
Not Vulnerable |
|||
12.2XG |
Vulnerable. Migrate to 12.2(8)T10 |
|||
12.2XH |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XI |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XJ |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XK |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XL |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XM |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XN |
Vulnerable. Migrate to 12.2(11)T9 |
|||
12.2XQ |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XS |
Vulnerable. Migrate to 12.2(2)XB15 |
|||
12.2XT |
Vulnerable. Migrate to 12.2(11)T9 |
|||
12.2XU |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2XW |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YA |
Element |
12.2(4)YA7 |
||
NAT |
Not Vulnerable |
|||
IPFW |
12.2(4)YA8 |
|||
12.2YB |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YC |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YD |
Vulnerable. Migrate to 12.3(2)T3 |
|||
12.2YE |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YF |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YG |
Not Vulnerable |
|||
12.2YH |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YJ |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YK |
Vulnerable. Migrate to 12.2(13)ZC |
|||
12.2YL |
Vulnerable. Migrate to 12.3(2)T3 |
|||
12.2YM |
Vulnerable. Migrate to 12.3(2)T3 |
|||
12.2YN |
Vulnerable. Migrate to 12.3(2)T3 |
|||
12.2YO |
Not Vulnerable |
|||
12.2YP |
Not Vulnerable |
|||
12.2YQ |
Not Vulnerable |
|||
12.2YR |
Not Vulnerable |
|||
12.2YS |
Not Vulnerable |
|||
12.2YT |
Vulnerable. Migrate to 12.2(15)T5 |
|||
12.2YU |
Vulnerable. Migrate to 12.3(4)T1 |
|||
12.2YV |
Vulnerable. Migrate to 12.3(4)T1 |
|||
12.2YW |
Element |
12.2(8)YW3 |
||
NAT |
12.2(8)YW3 |
|||
IPFW |
Not Vulnerable |
|||
12.2YX |
Migrate to 12.2(S) Release 3 or migrate to 12.2(14)SU March-2004 |
|||
12.2YY |
Vulnerable Migrate to 12.3(2)T3 |
|||
12.2YZ |
Vulnerable. Rebuilds available upon request. |
|||
12.2ZA |
Not Vulnerable |
|||
12.2ZB |
Vulnerable Migrate to 12.3(2)T3 |
|||
12.2ZC |
Vulnerable Not yet planned |
|||
12.2ZD |
Vulnerable No Migration path No planned fix |
|||
12.2ZE |
Vulnerable. Migrate to 12.3(3e) |
|||
12.2ZF |
Vulnerable. Migrate to 12.2(15)SL1 |
|||
12.2ZG |
Vulnerable No Migration path No planned fix |
|||
12.2ZH |
Element |
12.2(13)ZH3 |
||
NAT |
||||
IPFW |
Not Vulnerable |
|||
12.2ZJ |
Element |
12.2(15)ZJ3 |
||
NAT |
12.2(15)ZJ2 |
|||
IPFW |
Not Vulnerable |
|||
12.2ZL |
Element |
12.2(15)ZL1 |
||
NAT |
||||
IPFW |
Not Vulnerable |
|||
12.2ZM |
Not Vulnerable |
|||
12.2ZP |
Not Vulnerable |
|||
12.3-based Releases |
Rebuild |
Interim |
Maintenance |
|
12.3 |
Not Vulnerable |
|||
12.3T |
Element |
Not Vulnerable to H.323 endpoint/gateway/gatekeeper issues |
||
NAT |
12.3(2)T3 12.3(4)T1 |
|||
IPFW |
Not Vulnerable to IOS FW issue |
Cisco Software - Non IOS
In all cases, customers should exercise caution to confirm that the devices to be upgraded contain sufficient memory and that current hardware and software configurations will continue to be supported properly by the new software release. If the information is not clear, contact the Cisco TAC for assistance as shown in the Obtaining Fixed Software section.
Cisco CallManager Version |
First Fixed Regular Release |
---|---|
3.1 |
3.1(4b)spD |
3.2 |
3.2(3) |
3.3 |
3.3(2)spC 3.3(3) |
The Cisco PSIRT is not aware of any malicious exploitation of any of the vulnerabilities described in this advisory.
These vulnerabilities were discovered through the use of the PROTOS H.323 test suite developed by the OUSPG at the University of Oulu, Finland, in concert with NISCC Vulnerability Management Team, the UK Government CERT.
These vulnerabilities are present in other products not provided by Cisco, and this security advisory is being published simultaneously with announcements from the other affected organizations.
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
Revision 1.4 |
2004-October-08 |
Added a Bug ID to the Details section for the Cisco ATA18x Series Analog Telephony Devices description. Changed the software version in the Software Versions and Fixes section for the Cisco ATA18x Series Analog Telephony Devices description. |
Revision 1.3 |
2004-January-16 |
Clarified syntax of show process cpu | include CCH323 command in "Affected Products" section. |
Revision 1.2 |
2004-January-15 |
Clarified nature of affected releases in "Summary" and "Affected Products" sections; updated IOS software table for 12.2XB, 12.0, 12.1, 12.2B, 12.2S, and 12.2E; updated software link for IPSec-H323.exe in "Workarounds" section. |
Revision 1.1 |
2004-January-14 |
Under "Affected Products" section: Replaced "AS5xxx series platforms" with "IOS images with the "PLUS" feature set"; under "Cisco IOS Processing of H.323 Traffic", removed mention of AS5xxx platforms; updated note under "H.323 Endpoints" section; updated note under "Cisco IOS Processing of H.323 Traffic" section; updated IOS software table for 12.2XB, 12.1E, 12.2, and 12.0; changed all references of "Migrate to 12.2(19)" to "Migrate to 12.2(19)b"; under the "Workarounds" section, updated section on "Defining a Windows-based access control list to limit H.323 traffic from only locally trusted hosts"; under "Exploitation and Public Announcements" section, replaced mention of "UNIRAS" with "NISCC Vulnerability Management Team" |
Revision 1.0 |
2004-January-13 |
Initial public release. |
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A stand-alone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy, and may lack important information or contain factual errors. The information in this document is intended for end-users of Cisco products.