A vulnerability in the DHCP version 6 (DHCPv6) relay feature of Cisco IOS and IOS XE Software could allow an unauthenticated, remote attacker to cause an affected device to reload. The vulnerability is due to insufficient validation of DHCPv6 relay messages. An attacker could exploit this vulnerability by sending a crafted DHCPv6 relay message to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link: http://tools.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-20160323-dhcpv6 This advisory is part of the March 23, 2016, release of the Cisco IOS and IOS XE Software Security Advisory Bundled Publication, which includes six Cisco Security Advisories that describe six vulnerabilities. All the vulnerabilities have a Security Impact Rating of "High." For a complete list of advisories and links to them, see Cisco Event Response: Semiannual Cisco IOS and IOS XE Software Security Advisory Bundled Publication.
This vulnerability affects Cisco devices that are running a vulnerable release of Cisco IOS or Cisco IOS XE Software and have the DHCPv6 relay feature configured on one or more interfaces. By default, the DHCPv6 relay feature is not configured on any interfaces.
For information about which Cisco IOS and Cisco IOS XE Software releases are vulnerable, see the "Fixed Software" section of this advisory.
Assessing the DHCPv6 Configuration
To determine whether the DHCPv6 relay feature is configured on an interface, administrators can use the show running-config | i relay|^interface or show ipv6 dhcp interface command in the command-line interface.
The following example shows the output of the show running-config command on a router that has the DHCPv6 relay feature configured on the GigabitEthernet0/0/1 interface:
router#show running-config | i relay|^interface
.
.
.
interface GigabitEthernet0/0/1
ipv6 dhcp relay destination 2001:DB8::1941
.
.
.
The following example shows the output of the show ipv6 dhcp interface command on a router that has the DHCPv6 relay feature configured on the GigabitEthernet0/0/1 interface:
router#show ipv6 dhcp interface
GigabitEthernet0/0/1 is in relay mode
Relay destinations:
2001:DB8::1941
Determining the Cisco IOS or IOS XE Software Release
To determine which Cisco IOS Software release is running on a Cisco product, administrators can log in to the device, use the show version command in the command-line interface, and then refer to the system banner that appears. If the device is running Cisco IOS Software, the system banner displays text similar to Cisco Internetwork Operating System Software or Cisco IOS Software. The image name appears in parentheses followed by the Cisco IOS Software release number and release name. Some Cisco devices do not support the show version command or may provide different output.
The following example identifies a Cisco product that is running Cisco IOS Software Release 15.5(2)T1 with an installed image name of C2951-UNIVERSALK9-M:
Router> show version
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.5(2)T1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2015 by Cisco Systems, Inc. Compiled Mon 22-Jun-15 09:32 by prod_rel_team . . .
For information about the naming and numbering conventions for Cisco IOS Software releases, see White Paper: Cisco IOS and NX-OS Software Reference Guide.
No other Cisco products are currently known to be affected by this vulnerability.
Cisco has confirmed that this vulnerability does not affect Cisco IOS XR or Cisco NX-OS Software.
Additionally, customers may only download software for which they have a valid license, procured from Cisco directly, or through a Cisco authorized reseller or partner. In most cases this will be a maintenance upgrade to software that was previously purchased. Free security software updates do not entitle customers to a new software license, additional software feature sets, or major revision upgrades.
When considering software upgrades, customers are advised to consult the Cisco Security Advisories and Responses archive at http://www.cisco.com/go/psirt and review subsequent advisories to determine exposure and a complete upgrade solution.
In all cases, customers should ensure that the devices to upgrade contain sufficient memory and confirm that current hardware and software configurations will continue to be supported properly by the new release. If the information is not clear, customers are advised to contact the Cisco Technical Assistance Center (TAC) or their contracted maintenance providers.
Customers Without Service Contracts
Customers who purchase directly from Cisco but do not hold a Cisco service contract and customers who make purchases through third-party vendors but are unsuccessful in obtaining fixed software through their point of sale should obtain upgrades by contacting the Cisco Technical Assistance Center (TAC):
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html
Customers should have the product serial number available and be prepared to provide the URL of this advisory as evidence of entitlement to a free upgrade.
To help customers determine their exposure to vulnerabilities in Cisco IOS and IOS XE Software, Cisco provides a tool, the Cisco IOS Software Checker, that identifies any Cisco Security Advisories that impact a specific software release and the earliest release that fixes the vulnerabilities described in each advisory ("First Fixed"). If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories identified ("Combined First Fixed").
Customers can use this tool to perform the following tasks:
To determine whether a release is affected by any published Cisco Security Advisory, use the Cisco IOS Software Checker on Cisco.com or enter a Cisco IOS or IOS XE Software release-for example, 15.1(4)M2 or 3.01.4S-in the following field:
The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerability that is described in this advisory.
This issue was found during Cisco internal testing.
To learn about Cisco security vulnerability disclosure policies and publications, see the Security Vulnerability Policy. This document also contains instructions for obtaining fixed software and receiving security vulnerability information from Cisco.
Version | Description | Section | Status | Date |
---|---|---|---|---|
1.0 | Initial public release. | - | Final | 2016-March-23 |
THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS AND DOES NOT IMPLY ANY KIND OF GUARANTEE OR WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE. YOUR USE OF THE INFORMATION ON THE DOCUMENT OR MATERIALS LINKED FROM THE DOCUMENT IS AT YOUR OWN RISK. CISCO RESERVES THE RIGHT TO CHANGE OR UPDATE THIS DOCUMENT AT ANY TIME.
A standalone copy or paraphrase of the text of this document that omits the distribution URL is an uncontrolled copy and may lack important information or contain factual errors. The information in this document is intended for end users of Cisco products.